PGEM PRO is our advanced wall-mounted energy storage solution, designed for space-saving without sacrificing performance. With cutting-edge LFP technology and a high-capacity 280Ah cell, it offers an exceptional 8,000-cycle lifespan and high energy density.

Featuring seamless remote updates and global monitoring, PGEM PRO keeps firmware up-to-date and allows easy performance tracking from anywhere. Its intelligent BMS ensures efficient, safe management of battery performance.

  • Voltage: 51.2V
  • Capacity: 280Ah
  • Dimensions: 475*900*238mm/18.7*35.4*9.4inch
  • Weight: 115kg/253.5lbs
  • Lifespan: 8000 deep cycles 
  • Communication: CAN/RS485
  • 0.5C Continuous Power
  • 10 years warranty
  • 32 Units Stackable
  • Ultra safe LFP material
  • Short circuit protection
  • Flexible remote upgrade, Original firmware backup to prevent upgrade failure
  • Wide range inverter compatibility
  • Multi protection to avoid over discharge
  • Smart BMS management for longer lifespan
  • Active balancing charging, low self consumption

PGEM PRO

14.3kWh Low Voltage Battery System

PGEM PRO is our advanced wall-mounted energy storage solution, designed for space-saving without sacrificing performance. With cutting-edge LFP technology and a high-capacity 280Ah cell, it offers an exceptional 8,000-cycle lifespan and high energy density.

Featuring seamless remote updates and global monitoring, PGEM PRO keeps firmware up-to-date and allows easy performance tracking from anywhere. Its intelligent BMS ensures efficient, safe management of battery performance.

LuxpowerTek PGEM PRO 2 home energy storage battery
LuxpowerTek PGEM PRO 1 home energy storage battery
LuxpowerTek PGEM PRO 3 home energy storage battery
  • Voltage: 51.2V
  • Capacity: 280Ah
  • Dimensions: 475*900*238mm/18.7*35.4*9.4inch
  • Weight: 115kg/253.5lbs
  • Lifespan: 8000 deep cycles 
  • Communication: CAN/RS485
  • 0.5C Continuous Power
  • 10 years warranty
  • 32 Units Stackable
  • Ultra safe LFP material
  • Short circuit protection
  • Flexible remote upgrade, Original firmware backup to prevent upgrade failure
  • Wide range inverter compatibility
  • Multi protection to avoid over discharge
  • Smart BMS management for longer lifespan
  • Active balancing charging, low self consumption

FAQ

The PGEM PRO is a low-voltage lithium energy storage battery designed for residential and larger-capacity solar storage and backup applications.

The PGEM PRO has a capacity of 180Ah and a nominal energy capacity of 14.3kWh. It provides significantly more energy storage in a single battery unit compared with smaller 5kWh-class batteries.

The PGEM PRO can work with compatible LuxpowerTek low-voltage inverter series. For specific inverter models and BMS communication compatibility, please refer to the latest LuxpowerTek battery compatibility list.

Yes. Multiple compatible PGEM PRO batteries can be connected in parallel to increase total storage capacity and available battery power for larger energy storage systems.

It depends on your daily energy consumption, required backup time and maximum load. Each PGEM PRO provides 14.3kWh nominal energy, allowing substantial storage capacity with fewer battery units.

Yes. The built-in Battery Management System (BMS) communicates with compatible inverters to coordinate charging and discharging and provide battery status and protection information.

Yes. When paired with a compatible hybrid inverter, stored energy from the PGEM PRO can be used to supply backup loads during a grid outage. Actual backup time depends on SOC, connected loads and system configuration.

The PGEM PRO has an IP20 enclosure and is intended for indoor installation. It should be installed in a dry, well-ventilated location protected from rain, water and unsuitable environmental conditions.

Yes. When connected to a compatible LuxpowerTek inverter and monitoring system, key battery information such as State of Charge (SOC) and operating status can be viewed through the system monitoring platform.

Yes. Additional compatible PGEM PRO batteries can be added to increase total storage capacity. Battery condition, SOC, firmware and installation requirements should be checked before expanding an existing system.